- Aesthetic composition of a dramatic production as created by lighting, scenery, costumes, and sound.While elements such as painted screens and wheeled platforms were used in the Greek theatre of the 4th century BC, most innovations in stage design were developed in the Italian Renaissance theatre, where painted backdrops, perspective architectural settings, and numerous changes of scenery were common. Italian staging was introduced in England in 1605 by Inigo Jones for court masques. In the late 19th century staging was influenced by the new naturalism, which called for historically accurate sets. In the 20th century simplified stage design focused attention on the actor. Stage design has been greatly affected by advances in lighting, from the use of candles in the Renaissance to oil lamps in the 18th century and gas and electric lights in the 19th century. Modern stage lighting, which employs computerized control boards to achieve complex effects, can unify all the visual elements of a stage production. See also stage machinery.
* * *▪ theatreIntroductionthe aesthetic composition of a dramatic production as created by such aspects of stagecraft as scenic design, stage machinery, lighting, sound, costume design, and makeup.Scenic designEuropean and American theatreIn comparison with the history of Western theatre, the history of scenic design is short. Whereas the golden age of Greek theatre occurred more than two millennia ago, the intensive use of scenery in the theatre did not begin until after 1600, and the position of scenic designer—the individual responsible for the visual appearance and function of the scenic and property elements of a theatrical production—did not become a commonly credited production position until the mid-1920s. Robert Edmond Jones (Jones, Robert Edmond) is generally acknowledged as among the first credited scenic designers, for a 1915 production of The Man Who Married a Dumb Wife.The term scenery can include any noncostume visual element used in support of a production. In the context of this article, however, it will be defined as any nonpermanent two- or three-dimensional background or environmental element that is placed on the stage so as to suggest the historical period, locale, and mood of the play being performed. While properties—e.g., set props (sofas, chairs, draperies, and so forth) and hand props (any noncostume items handled by the actors, such as glassware, cutlery, or books)—do the same, they generally are not considered to be scenery.There was very little scenery used in Western theatres before the early 1600s. While Greek and Roman plays were performed outdoors in elaborate and imposing structures, there is little physical evidence to suggest that scenery, as defined above, was used on these stages. Medieval European drama used standardized scenic elements called “mansions (mansion)” (representations of heaven, hell, the Garden of Eden, and so forth) to depict the various locations needed in the liturgical drama that constituted the bulk of the period's plays. Mansions were often mounted in the nave of a church, on a platform in front of a church, or in a town square. They were also used in combination with pageant wagons (pageant wagon), which usually held between one and three mansions, were pulled from location to location, and were arranged to create the appropriate setting.The Renaissance was a time of development and experimentation in the arts. This creative reawakening affected the design of theatre structures as well as scenery. Some theatres, such as the Teatro Olimpico in Vicenza, Italy, had permanent sets built as part of their theatre architecture. Others, such as the Globe Theatre in London, had bare, open stages with no permanent scenic elements. Between the mid-17th and the mid-19th century, numerous theatres were built in cities and towns and on private estates throughout Europe.Opera houses were frequently among the first municipal buildings erected in the new towns and cities that were springing up in the American and Canadian landscape during the 19th century. The overwhelming majority of these theatres had proscenium (picture-frame) stages. The manner in which the scenery was created for these theatres was generally determined by the extent of the production program of the producing organization. Theatres with permanent companies and expansive production programs— La Scala in Milan, Covent Garden Theatre in London, and many European court theatres, for instance—employed resident artists to build and paint the scenery. Producing organizations with less-extensive production programs, such as traveling troupes, either employed itinerant artists and craftsmen or ordered stock scenery from manufacturers that existed in almost all major and many medium-sized cities in both Europe and North America by the middle of the 19th century. The stock sets produced by these manufacturers were not tailored to the specific needs of any particular play but instead depicted locations that were standard to most: a nobleman's library, a courtyard, a forest, and so forth. If a script called for a specific location—for example, a street scene—a producing organization would order the “street scene” stock set, which usually consisted of a drop (a cloth hung behind the stage) and wings (cloths hung parallel to the drop, at the sides of the stage), from the list of available scenes depicted in the catalogs of many scenic production houses. After the play closed, the set was put into storage until another play required a street scene; the set would then be reused, usually with little, if any, modification.In the mid-1800s a movement that was to reshape the theatrical world began. This movement, realism, which began partly as a reaction to the melodramas (melodrama) of the late 18th and early 19th centuries, produced some of the first plays that focused on social issues in the lives of ordinary citizens rather than on the actions of the aristocracy and monarchs. This shift of thematic focus caused a major innovation in scenery. Realism demanded sets that more faithfully reproduced everyday life. Beginning in the mid-1870s, realistic interior and exterior sets proliferated, and the level of spectacle seemed determined only by the scenic budget.The realism movement of the 19th century had brought realistic details to scenic design. But this focus on historical accuracy resulted in scenery that too frequently became more important than the play itself. It was not until the early 1900s that scenic design began to move beyond the period, country, and locale of the plays' settings to focus on the socioeconomic status of the play's characters and environment as well as the mood and spirit of the play. Modern European and American scenic design tries to help the audience understand and connect with a play by visually reinforcing all of these aspects.By the start of the 20th century, the design and production of stage scenery had become fairly standardized. The producer and the director—along with, sometimes, the playwright or the lead actor—created a ground plan of the required settings and contracted with a scenic production house to make the scenery. The staff of the scenic production house then created painted models of the sets and, after final approval, created scale drawings from which the scenery was built. Frequently the scenery was constructed by one company and painted by another. Permanent producing theatres with active production programs often employed in-house carpenters and scenic artists to create the scenery. By the turn of the 21st century, however, most scenic production studios—whether in-house or independent—had become all-inclusive, in that they built and painted almost all the scenery and many of the properties needed for a production. Specialty items—such as elements that needed engineering (trusses, elevators, and so forth), as well as period furniture and complex items that required specialized fabrication techniques and equipment—were frequently subcontracted to appropriate businesses.Role of the scenic designerApproaches to contemporary scenic design procedure are fairly uniform throughout the Western world. One guideline is generally followed: the design needs to be expressive of the mood and spirit of the play. The terms mood and spirit can be further defined. Generally, mood refers to the production's overall emotional quality—happy, sad, tragic, comic, and so forth. Spirit refers to the production concept—the style or manner in which a particular production is to be presented, as decided by the production design team. The director and producer almost always create the initial production concept. Depending on its clarity and the director's and producer's belief in it, the production concept may remain unchanged, or it may be modified as a result of input from the various designers.The process for creating a scenic design begins with the designer's closely studying the script for information it contains about the period, country, locale, mood, and spirit of the play, the socioeconomic status of its characters, and any other information that will help with development of the design. The designer also typically engages in research into the history of the period depicted in the play to learn not only the visual style of the period but its social context as well. The scenic designer also attends numerous production meetings in which budgets, the production venue, and the details of the play and its production are discussed.The scenic designer, after synthesizing the information gathered from the script and the various production meetings, normally creates a series of thumbnail sketches that show the major outline, character, and feeling of the sets. These sketches are discussed in additional production meetings and modified as necessary. After a preliminary design has been approved, the scenic designer creates colour renderings and, sometimes, cardboard models of the designs. Again, these renderings and models may be modified as a result of additional discussions. After final approval of the design, scale drawings of the sets are created and provided to the production studio for construction of the scenery.At the turn of the 21st century, many scenic designers still preferred to work with traditional materials and techniques—pencil, paper, ink, paint, and pastel—but an increasing number used computers to do their sketches and drafting. The advantages of computer drawing (computer-aided engineering) proved to be numerous. Designers were able to create and quickly modify sketches and final colour renderings of the settings. Computer drafting also allowed the designer to create very accurate and easily modified elevations (views of a set as if seen from ground level) and ground plans (as if seen from above). Likewise, computers enabled designers for the first time to create a three-dimensional view of a set and its location relative to the permanent structures of a theatre in a manner that allowed the set to be viewed from any seat. Such a view greatly aided designers in determining hanging positions for the various elements that prevent the audience from seeing backstage. Computer software also permitted the designer to create real-time animations that choreographed the sometimes extremely complex movements of scenic elements that take place during some scene shifts.Asian theatreThroughout history, Western theatre has been significantly influenced by religion, probably because, in almost all Western cultures, theatrical presentations began as an outgrowth of local religious practices. (See Western theatre: The origins of Western theatre (theatre, Western).) Dominant religions in other areas of the world similarly influenced theatrical activities. For example, in regions where Islam (Islamic arts) is the primary religion, the development of theatre faced prohibitions against the presentation of images of living beings. Nonetheless, popular plays based on folkloric themes thrived. These performances did not occur in theatres or use scenery. The only staging elements employed were, at most, a rug laid on the ground and a canopy suspended overhead.Almost all Arabic-speaking cultures also have a strong tradition of shadow-puppet theatre; among the most prominent of these traditions is the Karagöz puppet show. Shadow puppets, so-called because the audience sees only the shadows of the puppets projected on a cloth screen, thrived by sidestepping Islamic prohibitions. Because the audience never saw the puppets' human operators and because the puppets' two-dimensional jointed bodies were translucent, the shadows that they produced were not considered representations of humans. Like other forms of popular theatre in the Arabic-speaking world, shadow-puppet theatre uses no scenery.Theatre in India benefited from a dominant religion (Hinduism) that encouraged theatre. Presentations and ritual performances seem to have been common in India from earliest times. The Natya-shastra (Nāṭya-śāstra) (“Treatise on Dramatic Art”), written around the 2nd century CE, described three sizes and shapes of extant playhouses. The theatres, most of which were rectangular, were divided equally between the auditorium and the stage. The stage was also divided into two equal parts: the performing area and backstage. The performing stage was separated from backstage by a wall with two doorways. The area between the doorways, and much of the stage, was decorated with symbolic paintings and carvings. No scenery was used. The theatres used for the performances of Indian folk plays normally have an open stage, devoid of scenery, that is surrounded on three sides by the audience.Although China's history of public performance dates back to at least 1500 BCE, a fully developed dramatic form did not begin to emerge until the Song dynasty (960–1279). Prior to the 10th century, public entertainments resembled modern circuses or variety shows in their combination of music, dance, and displays of athletic skills. The Chinese literary theatre, marked by its script-based production style (as opposed to the more improvisational theme-based folk theatre that had been in vogue), began during the Yuan dynasty (1206–1368). The staging for this type of theatre is similar to that of Indian theatre. A painting dated 1324 shows an essentially bare stage; a decorative wall hanging is depicted at the centre of the wall at the rear of the stage, and two doorways are on either side of the hanging. No scenery is used in the performance of Chinese classical theatre today, although there are historical records of props such as tables and chairs being employed.In Japan, Noh (Noh theatre) drama began developing in earnest in the 12th and 13th centuries, and its form was essentially set by the early 1600s. Very little about this dramatic form has since changed. The shape, style, and dimensions of the Noh stage are closely prescribed, and there is no scenery used. Kabuki theatre began in 1603 when Okuni, a female temple dancer, performed on a temporary stage set up in the river flats in Kyōto. Kabuki, which borrowed heavily from the Noh and other art forms, was very popular with the merchant and lower classes, while Noh performances were reserved for the samurai and noble classes.Kabuki performers at first used the Noh stage but soon began to modify it. Originally relegated to outdoor performances on temporary stages, Kabuki troupes were in 1724 permitted by the government to use enclosed theatres. The advent of such theatres encouraged the development of advanced stage machinery, including elevator traps (trap) (1736), elevator stages (1753), and revolving stages (revolving stage) (1758). The development of these complex mechanical systems coincided with the introduction of scenery into Kabuki theatre. As the stage machinery became more sophisticated—concentric revolving stages were first used in 1827, for instance—scenic elements became more and more complex.Unlike other theatre traditions in Asia, Kabuki makes extensive use of scenery, which is used to characterize every locale. But there is a significant difference between scenery used in Western theatre and that used in Kabuki. Where Western scenery typically attempts to create the illusion of place by transforming the stage into that place, Kabuki scenery instead decorates the stage. As a result, locale is suggested in Kabuki theatre rather than created. To help support this nonillusionary premise, Kabuki scenery is changed in full view of the audience by means of a revolving stage, elevator traps and stages, grooves, and visible stage attendants.Howard Bay Clive Barker Ed.Stage machinery can be divided into two general categories: permanent machinery, which is equipment that is part of the theatre's structure, and temporary machinery, which is equipment that is taken into the theatre to be used in conjunction with a specific production.There are three general types of stage configurations: the proscenium stage, the open stage (or thrust stage), and the arena stage (also called theatre-in-the-round). Both open and arena stages generally have a permanent lighting grid—a network of steel pipes used for hanging lighting instruments—above the stage and auditorium spaces. All three types of theatre can have permanent stage machinery—such as flying systems, revolving stages, and slip stages—although most such machinery is associated with the proscenium stage.Flying systemsFlying systems are an important piece of stage machinery for proscenium-stage theatres. These systems are used to lift (or fly) scenery from the stage into a space above the stage (the fly loft) by means of mechanical hoists (hoist). There are two main types of flying systems: hand-operated and machine-driven. Hand-operated systems can be further subdivided into two types: rope-set, or hemp, systems and counterweight systems. The rope-set system normally has three or more ropes attached to a metal pipe, called a batten, above the stage. The ropes pass over loft blocks on the grid above the stage. Then, at the side of the stage house, they pass over another set of blocks (known as head blocks) and thence down to the fly gallery, where they are tied off at the pin rail. In order for the scenery to be raised, it is attached to the batten; when the operator pulls down on the ends of the ropes, called operating lines, that drop from the head blocks to the pin rail, the scenery rises. If the weight of the scenery is too much to be lifted by the operator, sandbags—used to counterbalance the weight of the scenery—are attached to the operating lines. This system is archaic and inherently dangerous, and it is rarely used today, although it was the standard method of flying scenery from the early 1600s until the introduction of the counterweight system in the early part of the 20th century. The principles underlying the rope-set system can also be found in the counterweight system. The latter, however, is considerably safer and easier to operate. Steel cables are used to support the batten. The offstage ends of these cables are attached to a structure called the counterweight arbor. With the batten lowered to the stage floor, the objects to be flown are attached to the batten, and metal weights sufficient to counterbalance the weight of the equipment being flown are loaded onto the counterweight arbor from the loading platform. The up-and-down movement of the counterweight system is controlled by the system's operating line, which forms a closed loop in which one end of the rope is attached to the top of the counterweight arbor. The line then passes over a head block, down through the rope lock, to the tension pulley; it then passes back up to attach to the lower end of the counterweight arbor.At the turn of the 21st century, there were still many hand-operated flying systems in use. But most of the newly installed machine-driven flying systems were powered by electricity. Such systems can, in turn, be divided into several categories defined by the type of hoist used. Some systems use electricity to provide the pulling power but still require counterbalancing; this type is reliant on electrical counterweight-assisted hoists. There are, in turn, two forms of electrical counterweight-assisted hoists: traction drive and linkage drive. In the traction-drive system, the hoisting line–counterweight system is not directly coupled to the electric motor drive, and slippage may occur during acceleration and deceleration of the payload, according to velocity and the weight of the payload. Consequently, traction-drive hoists are utilized only when a relatively constant weight is lifted at a constant velocity; such hoists are often used for curtains and light bridges. The linkage-drive hoist is similar to the traction-drive hoist, except that the hoisting lines are attached directly to the motor.In other systems electricity may provide both the lifting ability and the force needed to counterbalance; these are a second type of hoist, called a pure-power hoist. Such hoists consist of a motor, a brake, a gear reducer, and a drum around which several hoisting lines wind.The third type of hoist powered by electricity is a hydraulic hoist, in which an electric motor is used to run a hydraulic piston, which in turn moves the hoisting lines. The advantages of this form of machine-driven flying system are that the electric motor does not have to be physically near the fluid drive, so the system is virtually noiseless, and that the operator may divide the power between any number of pistons, a feat not possible with an electric motor alone.Lifts (elevator)Lifts are used in the theatre to move platforms, actors, scenery, and other production elements above or below the stage floor. In contrast to the hoist, which is supported by the overstage structure, the lift is supported and guided by the stage floor or the cellar floor below the stage. The two general types of lifts are the architecturally integrated lift and the temporary production apparatus.Architecturally integrated lifts must be designed in accordance with local building-safety codes. One type of lift, the direct-plunger lift, is hydraulically driven, using a piston attached to a portion of the stage floor. The piston operates under hydraulic pressure and is expanded and collapsed to elevate the associated platform. The other type, the screw-actuated lift, is either electrically or hydraulically driven and is coupled to a vertical screw through a nut in which the upper end of the screw is connected to a portion of the stage floor.The layout and installation of permanent architecturally integrated lifts must be carefully determined; the frequency of use and the type of events to be accommodated must be envisioned, along with the attendant inflexibility of the permanent mechanization of the stage floor. In general, architecturally integrated lifts are successfully employed where they are designed to meet the specific production needs of a permanent resident company.Horizontal drivesPermanent horizontal drives, which are typically electrical or hydraulic, are used to move slip stages and revolving stages that are built into the theatre structure. Temporary horizontal drives are used in specific productions to rotate and propel scenery, actors, and props from offstage to onstage. Although the articulation of horizontal motion on the stage is unlimited, there are several established configurations that are easily identifiable. These include the wagon, in which scenery is built on a low platform mounted on casters so that it can be quickly rolled onstage and offstage; the jackknife stage, similar to the wagon except that it is anchored at one corner from which it pivots onstage and offstage; and the revolve, or turntable, in which several settings are built on a huge circular platform that is turned so that only the appropriate setting may be seen through the proscenium. In each of these, the scenery may be changed when the unit is offstage and then rolled back on.The computerized controllerThe development in the late 20th century of the computer-driven controller—generally known as “show control”—greatly enhanced the flexibility and usefulness of drive systems in the theatre. The term show control refers to the process of using computers to precisely control the movement of various pieces of electrically and hydraulically powered equipment. Prior to the adoption of computer controllers, the ability to control more than one system at a time was, to a great extent, dependent on the physical and mental dexterity of the control console operator. Computer controllers—which repeat commands precisely and exactly—changed that. Aided by computers, the console operator could precisely and exactly determine the operational parameters (start time, speed, duration, and so forth) for every piece of powered equipment used in a show. By the turn of the 21st century, production designers were able to choreograph complex scenic movement as part of the overall visual spectacle of a production.Clive Barker William Cruse J. Michael GilletteStage lightingEarly historyThe classic Greek theatron (literally, “a place of seeing”) was built in the open air, usually on a hillside, and placed so that the afternoon sunlight came from behind the audience and flooded the performing area with light. The larger Roman theatres were also outdoors, but the added luxury of a coloured awning stretched over the spectators softened the glare of the sun. Later, in the Middle Ages, miracle plays (miracle play) and mystery plays (mystery play) were primarily performed outdoors on the front steps of the church and the adjoining square, although the first dramatized biblical scenes were performed as part of, or following, mass inside the church. There is no record that these scenes were lighted any differently from the mass itself. In England the pageant wagon, complete with actors and properties, was drawn through the main street of a town. Until the 16th century, the theatre continued to be mainly an outdoor institution.Under the patronage of the aristocracy in Italy, private performances, pageants (pageant), and tableaux began to be given indoors. Sebastiano Serlio (Serlio, Sebastiano), an Italian architect, gave considerable attention to theatre design, and in a treatise written in 1545 he discussed theatre construction and the creation of lighting effects. He recommended placing candles (candle) and torches behind flasks filled with amber- and blue-coloured water. Andrea Palladio (Palladio, Andrea)'s indoor theatre, also in Italy, used common light sources: torches, pine knots, open-wick lamps, and tallow candles. In England at the end of the 16th century, the Globe Theatre was used for summer performances of William Shakespeare's plays, but in winter performances were given in the completely enclosed Blackfriars Theatre. Artificial light, produced mainly by candles, was used in several indoor theatres to light the stage and the auditorium.In the early 17th century, Inigo Jones (Jones, Inigo) introduced several innovations in lighting and stagecraft, using reflectors (mirror) to intensify the light sources and making use of colour on stage. The earliest known definite description of stage lighting may be found in Architectura Civilis (1628; “Civil Architecture”), by Joseph Furttenbach (also spelled Furtenbach). He describes the use of oil lamps and candles set in a row along the front edge of the stage but out of sight of the audience, and he also mentions vertical rows of lamps behind each wing at the sides of the stage. The common method of lighting the stage and auditorium was by means of tallow candles. As seen in old prints, these candles were mounted in crude hoops or chandeliers, which were hoisted aloft on pulleys to hang in dripping splendour. Gold decorations applied to the interior of the auditorium caught the many reflections. The inconvenience of the lighting system was that candles were expensive and hard to control. The twisted wicks had to be constantly trimmed during the performance, and this was the duty of the snuff boy. A transformation from light to darkness was effected by the agile skill of the candle snuffers.When David Garrick (Garrick, David) used footlights at the Drury Lane Theatre in 1765, he masked the candles with metal screens. By 1784, when Richard Brinsley Sheridan (Sheridan, Richard Brinsley) managed the Drury Lane, all lights used to illuminate the stage were out of sight, hidden by the now familiar wings and borders.The floating oil wick lamp was replaced after 1783 by the Argand (Argand burner) oil lamp, in which the cylindrical wick was enclosed in a glass chimney to steady the flame and provide a brighter, whiter, and cleaner light source. The chimneyed oil lamp eventually replaced the candle, but it was still hung in clusters above and bracketed to the walls. At the Haymarket Theatre in London, the oil lamps had chimneys of white and green glass that were controlled by levers, so that raising or lowering the chimneys could effect light changes. Actually, rather than subtly shifting the quality of the light, the chimneys' movement merely made the actors and scenery more or less visible. Stage design and stagecraft had now advanced as far as was technically possible under the limitations of low-intensity stage lighting.The first major advance in several centuries was the introduction of gas lighting. Near the end of the 18th century, the Scottish engineer William Murdock (Murdock, William) developed a practical method to distill gas from coal for illumination. The first successful adaptation of gas lighting for the stage was demonstrated in the Lyceum Theatre, London, in 1803 by a German, Frederick Winsor. The Chestnut Street Opera House in Philadelphia installed a gas lighting system in 1816 and supplied its own gas by installing a gas generator on the premises. (Gas stations and city mains did not come into use before 1850.) The advantages of gas lighting were immediately realized and exploited, despite the initial cost. No new methods of lighting, however, were devised for stage lighting. The conventions remained the same: footlights (a row of lights across the front of the stage floor), borderlights (a long horizontal row of lights used for the general lighting of the stage from above), and striplights (a row of lights usually mounted in a trough reflector (mirror) and placed in the wings to illuminate specific portions of the stage or setting).Even without a chimney, an open gas jet flame was brighter than oil lamps or candles. The additional advantage was control; by varying the control valves from a central point, a smooth increase or decrease of light could be effected, and at variable speeds. For the first time, to add to the realism of the play, the auditorium lights could be darkened. Elaborate central control systems were devised, with a main regulator, branch mains, secondary regulators, and valves. This growing array of valves and pipes was organized into circuits and displayed on the “gas table”—the forerunner of the modern switchboard.But there were also disadvantages to gas: heat, offensive vapours, and the serious fire hazard of the open flame. Protective codes were soon established that necessitated the use of guards, screens, and glass chimneys. In 1890, after the introduction of electric lighting, the incandescent gas mantle was developed (see incandescent lamp). Although the mantle greatly improved the quality of light—which was brighter and whiter—the hazards of fire still remained.Although Thomas Drummond, a British engineer, invented the limelight in 1816, it did not come into general use until some 30 years later. A limelight produces light by directing a sharp point of oxyhydrogen flame against a cylindrical block of lime. The tiny area of lime becomes incandescent and emits a brilliant white light that is soft and mellow. As the block of lime is slowly consumed by burning, it has to be slowly and constantly turned by an operator to supply the flame with a fresh surface. Since the brilliant area was very small, the addition of a mirrored reflector was necessary to give accurate control.The intensity of the limelight permitted it to be directed onto the stage from the auditorium. Since it offered control as well as intensity, the limelight was quickly adapted to follow individual performers around the stage. The sharpness produced by the small point source made possible the creation of realistic effects, such as sunlight and moonlight, and moving effects, such as clouds, water, and fire.Electrification (electricity)An advance of great importance was the introduction of the electric (electric arc) carbon- arc lamp, which was exhibited in experimental form in 1808 by Sir Humphry Davy (Davy, Sir Humphry, Baronet). The Paris Opéra developed the earliest electric arc effect—to represent a beam of sunlight—as early as 1846. By 1860 the Paris Opéra had also developed a lightning machine, a rainbow projector, and a luminous fountain. Most important, the company made the earliest spotlight, a carbon arc and reflector (mirror) housed in a hood, which included a lens and a shutter.The next great advance in lighting was the development of the incandescent (incandescent lamp) electric lamp, in which light is produced by a filament electrically heated to incandescence. The invention of a practical electric lamp by Thomas Edison (Edison, Thomas Alva) in 1879 marked the beginning of the modern era of stage lighting. Gas was quickly discarded; within one year the progressive Paris Opéra introduced the new system. Two years later, at the Electrotechnical Exposition in Munich, a small theatre was erected that used electric lighting exclusively for both stage and auditorium. The success of the experiment received worldwide acclaim. In London the Savoy Theatre was the first to install the new lights; in Boston the Bijou Theatre followed the new trend in 1882. The following year the Landestheatre in Stuttgart, the Residenztheatre in Munich, and the Vienna State Opera were among the first completely electrified theatres.At the turn of the 20th century, incandescent lamps were in almost universal use for stage lighting, but no new methods or techniques of lighting appeared. The conventional footlights, borderlights, and striplights were merely electrified, and the arc light was used for concentrated light sources. Gradually, new improvements provided brighter lamps that were both more durable mechanically and available in larger wattages. Metallic filaments replaced carbon, and in 1911 drawn tungsten filament lamps (filament lamp) appeared. The use of inert gas in place of a vacuum produced lamps of even higher efficiency and larger sizes. The introduction of concentrated coil filaments made practical the development of the incandescent spotlight. The refinement of the incandescent spotlight added an exciting new tool for the advancement of stage lighting and the further development of stagecraft. Gradually the arc spotlight was replaced by the new incandescent spotlight, which, in turn, gave way to the tungsten-halogen lamp.In his music dramas, German composer Richard Wagner (Wagner, Richard) suggested new possibilities for the use of light and design in a unified production—a lyrical synthesis. Adolphe Appia (Appia, Adolphe) and Edward Gordon Craig (Craig, Edward Gordon) gave tremendous impetus to the new plastic stagecraft. They conceived of the stage as a cubic volume of space bathed in a continuous play of functioning light. All the vast optical effects of Baroque design previously obtained with paint were now possible by means of light.About 1902, in Germany, Mariano Fortuny (Fortuny, Mariano) developed an elaborate system of soft reflected light using arc lights bounced off coloured silk fabrics. The simulation of natural lighting was remarkable, but the entire mechanism was too bulky and intricate and required the construction of a special theatre. In the course of his experiments, Fortuny evolved a dome-shaped cyclorama, its rear wall surfaced in plaster. Flooded with light, it gave the illusion of infinite space and was the perfect means of simulating spectacular sky and background effects. Because it was dome-shaped, however, it occupied a large amount of stage space and tended to distort optical projections. In modified form, as a curved, hanging cyclorama, it became an indispensable tool of the new stagecraft. Earlier, Sir Henry Irving (Irving, Sir Henry) had used transparent coloured lacquers to coat lamps to produce colour effects, using separate circuits for each colour. Irving was also the first producer to introduce organized light rehearsals in his productions.David Belasco (Belasco, David), with his electrician Louis Hartman, developed a standard of realism in stage lighting that anticipated the motion picture and went on to dominate the 20th century. In their lighting laboratory, Belasco and Hartman developed and refined many new lighting instruments. Individual sources were developed and used to light the acting areas from above the stage as well as from the auditorium.Lighting controlDimmersA dimmer is an electrical device by which the intensity of stage lights connected to it can be controlled. There are two methods used to control the flow of electrical current through a dimmer: mechanical and electronic (electronics). Mechanically controlled dimmers require the physical manipulation of an axle running through the core of the dimmer to adjust current flow. An electronically controlled dimmer uses a low-voltage control system to adjust the current flow in the high-voltage load circuit. The advantage of electronic control is that it allows the dimmer to be controlled from a remote location.There are three basic types of mechanically controlled dimmers: resistance, saturable core, and autotransformer. The resistance dimmer was the first commercially successful theatrical dimmer. Developed in the late 19th century, it was portable, efficient, and extremely rugged, and, because it ran equally well on both alternating current (AC) and direct current (DC) power, the resistance dimmer survived for decades as the standard in commercial theatre throughout the world; its use was in general decline after the 1950s. By the end of the 20th century, it was no longer being used. A saturable core dimmer uses a small DC current to magnetize an iron core through which AC current flows. As the level of magnetism increases, the conductivity of the core also increases; more AC load current is thus able to pass through it, and any lights connected to the dimmer will come on. Like the resistance dimmer, however, the saturable core dimmer is no longer used. The autotransformer dimmer controls current flow by varying the voltage in the circuit. It was rarely used to control stage lights, but at the turn of the 21st century it was still being used in some theatres to control house lights.The first electronically controlled dimmer was the thyratron tube dimmer, developed by George Izenour in 1948. It was the first dimmer to make use of gating—a rapid turning on and off of the current flowing through the load circuit—to control light output and intensity. The thyratron vacuum tubes were large and noisy, and they required a considerable warm-up period before they worked properly. They also needed frequent maintenance, did not last very long, and were expensive. But the demonstration that the gating principle could be used for effective intensity control paved the way for silicon-controlled rectifier (SCR) dimmers.The magnetic amplifier dimmer, developed in the 1950s, was in essence a saturable core dimmer that used electronic, rather than mechanical, control to vary the level of magnetism in its iron core. While it was an improvement over the saturable core dimmer—because the electronic control allowed the dimmer to be remotely controlled—its control circuit needed almost daily maintenance to run properly. Theatrical applications of the magnetic amplifier dimmer lasted only a few decades; it was quickly superseded by the SCR dimmer, which became the standard in stage lighting in the 1960s. Like the thyratron tube dimmer, it operates on the gating principle, but its on-off cycle, at over 100 times per second, is significantly faster. This rapid on-off cycling controls the flow of current through the dimmer. The electronic dimmer control circuit tells the SCR dimmer when and for how long to conduct the current during each cycle. For example, if the dimmer is set at half intensity, it conducts for half its cycle and does not conduct for the other half. This causes the light connected to the dimmer to glow at half intensity. If the dimmer is set at three-quarters intensity, it conducts for three-quarters of the cycle and does not conduct for the other quarter, causing the light to glow at three-quarter intensity. The on-off cycling in an SCR dimmer occurs so quickly that the individual on-off cycles are indiscernible.Control consolesThe earliest electrical dimmer switchboard, or control console—a device that centralizes control of the intensity of the stage lights—resembled the gas table that was used with gas lights in the late 19th century. These first electrical switchboards, introduced in Europe and the United States in the late 19th century, were used to control groups of resistance dimmers, which were permanently wired to circuits in the footlights or borderlights. The only open (or flexible) dimmer circuits were the floor and wall pockets (electrical outlet boxes set in the floor and walls of the stage area). Large banks of resistance dimmers were normally located backstage in the wings and in close communication with the stage manager, who could see what was happening on the stage. Later, the development of headset sound systems—which allowed the stage manager to remotely communicate with the light-board operators—allowed portable resistance switchboards to be placed in the cellar or other places with no view of the stage. This, in turn, freed up more offstage space for the actors and scenery. The introduction of electronically controlled dimmers allowed the dimmers to be placed anywhere in the theatre; likewise, the control console could be placed in the rear of the auditorium, where the operator had a full view of the onstage action.Two categories of electronic control consoles emerged during the 20th century but had become obsolete by the century's final decades: group master and preset. (A combination board is sometimes identified as a separate category of control console, but it simply combined group master and preset controls.) The group master and preset boards were a direct carryover from the layouts first used on gas tables. On a group master console a so-called grand master—an electronic fader or control that controlled the output of two or more submasters—and each submaster normally controlled between two and eight individual dimmers. The preset board was derived directly from the group master board, but the preset board allowed dimmer intensity levels to be set in advance, before they were needed onstage. Preset boards typically had anywhere between 2 and 10 preset banks; each bank controlled a specified number of dimmers. Such boards also included a cross-fader, a device that allowed the lighting controlled by one preset bank to be gradually replaced by that of another preset bank.The computerized control console had by the turn of the 21st century replaced all other types of systems. Such consoles use computer memory to store dimmer intensities for each cue. They also store fade times and have numerous capabilities that simply cannot be duplicated by any other type of control system. Of particular note is the ability of computerized consoles to repeat tasks consistently and accurately. That repeatability means that the lighting will look exactly as the designer intended for each and every performance. Prior to the introduction of the computer board, this level of precision was simply unobtainable even with the best board operator.Projections and special effectsA significant amount of lighting equipment has been developed for special effects. Standard effects include the representation of moving clouds, rippling water, fire, rain, snow, rainbows, and fireworks. For practicality, most special effects are built around a standard spotlight housing. The effect head, containing a painted or photographic transparent disk and the mechanism for revolving it, is placed in front of the spotlight housing. An additional objective lens is used to magnify and focus the image.The oldest effect projector, which dates from the World War I era, is the Linnebach lantern, often called a “scene” projector. It is simple both in principle and in construction. A concentrated light source is placed in a deep black box, and a painted slide is placed on the side of the box that is left open; since light travels in straight lines, the design painted on the glass is thus projected against a drop onstage, greatly enlarged, at a relatively short distance. Since no lens is used in a Linnebach lantern, the light source must be powerful and concentrated. The design must be simple and bold, for any line narrower than the point source itself will be lost. The overall effect is stylized and borders on the abstract. Rear projection with at least two projectors is required for any ambitious production. Large incandescent lights replaced the original carbon arcs (electric arc) in the Linnebach lantern.In the mid-20th century there was renewed interest in the use of projections, and the development of new projection equipment provided a powerful instrument to produce effects not previously possible. After World War II, at the music festivals at Bayreuth, Ger., Richard Wagner's grandson Wieland reduced three-dimensional scenic elements to the barest essentials and then flooded the stage with multiple overlapping projected patterns. In subsequent years additional scenic elements were added to give variety of texture and depth to the flow of light and pattern. Still later, at the Festspielhaus in Salzburg, Austria, the productions of Wagner's music dramas designed by Gunther Schneider-Siemssen elaborated this concept to achieve even more dramatic and sumptuous effects; Schneider-Siemssen filled the vast, extra-wide stage with patterns of light in depth, softened with scrims (loosely woven meshes that diffuse the light) and translucent drops (backdrops with sections dyed to transmit some light). The Czech designer Josef Svoboda did more than any other designer during the second half of the 20th century with “visions in space.” For some productions, he used a direct, journalistic approach, massing three-dimensional screens to create a montage effect with slides and film. Polyvision, a production conceived and executed by Svoboda for the Czech pavilion at the 1967 international exhibition at Montreal, was a brilliant multimedia experience. In his other productions, which were equally stylized but more indirect and abstract, he used alternating surfaces of scrim and scenic elements to catch the patterned light, cast complex shadows, and float in depth before a seemingly infinite background.Innovative contributions to lighting and the use of projections were also made in American dance (modern dance) during the second half of the 20th century. Alwin Nikolais (Nikolais, Alwin) made very original use of dancers (dance), costumes, light, and projections to form moving geometric and abstract designs. At times, the moving bodies of the dancers in his productions became the screen for the projections. Robert Joffrey (Joffrey, Robert)'s production of his ballet Astarte (1967) used a unique combination of film and slides on a moving, pulsating screen.By the early 21st century, digital projections had become the standard mode of projection in the theatre. The early generations of digital projectors, which first appeared in the 1980s, were not sufficiently bright for stage use. But technological advancements made after the turn of the century resulted in projectors bright enough for just about every theatrical use. The advantages of digital projections are many: the projected images can be still images or video; the “slides” are computer files that neither fade nor burn out as a result of the heat of the projector lamp; and the images can be created by hand, computer, or a combination of the two. Computer imaging therefore provides the projection artist with a much wider creative palette than ever before.Many contemporary plays permit no approach other than realism, which must be achieved by suggestion. Nature provides the model. On a cloudy day, the overcast sky diffuses the direct sunlight and produces a soft, shadowless light of low intensity and cool colour. Intense “sunlight” onstage and the attendant light of the bright sky together produce reflected light that diffuses or fills in shadows, while the ambient light of the stage “Moon” reflected from sky, trees, and buildings is too weak to wash out the shadows. So, by means of the direction, diffusion, and intensity of light, as well as its colour, it is possible to suggest time, place, and season.The means of suggesting natural lighting indoors are more arbitrary. The simulated sky or sunlight seen through a door or window—a scenic element provided by the dramatist and the designer—is essential to indicate the time of day or night. To render the feeling of bright daylight flooding a room, the strong motivating light (i.e., light that suggests the direction of its source) must be supplemented with additional light from other directions for adequate illumination. If only a sliver of sunlight creeps through a parted curtain in a dark room as the scene begins, the mood may be retained through the gradual illumination of important areas as the scene progresses. Artificial light indoors is easier to suggest because it more closely approaches the normal quality of stage lighting. Actual light fixtures are used onstage to suggest the sources of the light, and opaque shades can be used on some of these fixtures so that they cast actual patches of light against walls and furniture. The exteriors seen through doors and windows are darkened and different in colour from their appearance in a brightly sunlit scene. The walls fall off in shadow even though the general illumination is smoother and more diffused than in daylight. Light serves as a unifying medium for the stage composition. It is a mobile and changing accent that reinforces the action, sustains the mood, and focuses the attention of the audience. Light and shade define the size and shape of objects, as do brightness and contrast, but it is colour that creates mood, atmosphere, and an emotional response from the audience.The creative concept formed for lighting a production requires that the essential qualities of the play be understood and absorbed. The theme or main line of the script may suggest an overriding motif: enervating heat, ominous clamminess, dappled sunlight, penetrating northern light, a feeling of being in limbo or underwater. The final choice must satisfy the particular qualities of the production and the concepts of the playwright, director, and actors, as well as the designer. Run-throughs in the final period of rehearsals often reinforce previous impressions and suggest refinements in the rhythmic changes of light required. The actors' performances may also suggest to the designer lighting changes that can enhance the emotional range of the production.Ralph Holmes J. Michael GilletteSound designTechnological innovations of the 20th centuryPrior to the 1930s, the manner in which sound in the theatre was produced had not changed for more than 2,000 years. Music was played by musicians present in the theatre. Sound effects (sound effect) were produced by people who mechanically created sounds during every performance of the show. In the 1930s, however, the recording industry expanded rapidly throughout the world. Along with recordings of classical and popular music, the first sound-effects libraries were developed. These recordings, made on low-fidelity 78-rpm (revolutions per minute) records, contained short tracks of many different sounds, from barking dogs to steam locomotives. First developed for the burgeoning radio market, sound libraries were soon adopted by theatre technicians. The use of recorded preshow and intermission music to help set the mood of the production became fairly commonplace. Although many sound effects were still produced live, some directors began in the 1930s to make use of prerecorded material. However, because the playing of such material depended on a person's ability to place a phonograph needle onto a record at just the right time and in just the right place and to adjust the phonograph's volume on cue, the quality of these effects was often uneven.In the early 1950s there were several simultaneous developments in the audio industry that ushered in the modern era of sound in the theatre. Advances in electronic engineering greatly enhanced the fidelity of recording and playback equipment. The development of high-fidelity magnetic-tape recorders and long-play (45- and 331/3-rpm) records as well as of sophisticated amplifiers, loudspeakers, and speaker enclosures all contributed to a previously unobtainable level of realism in the reproduction of sound.In addition to high-quality playback, magnetic recording tape offered two other advantages over records: it could begin playing all but instantaneously, and it could be spliced, which meant that it could be edited, with sounds arranged and rearranged to suit the needs of a particular production situation. Additionally, for the first time the effects and the music needed during a production could be played from a central location. The playback deck as well as the amplifiers and mixing and equalization equipment were typically housed in a booth at the back of the auditorium. Portable loudspeakers were placed wherever needed on the stage or in the auditorium. Through the use of a playback mixing console (also called a mixer or a mixing desk), the sound operator could direct the sound for a particular cue to its appropriate location at a specific loudness level. It therefore became possible for one operator to run all of the sound cues from the sound booth during a production. Finally, the introduction of tape reduced the number of effects specialists needed; prior to the use of recorded sound effects, it was not unusual for a production to require a crew of six or more to create the effects during a performance, but afterward only one or two nonspecialist crew members were needed, primarily to move speakers and other equipment.The changes to sound in the theatre over the ensuing three decades were again technologically based. Experimentation with multitrack recording and playback occurred in a variety of venues, and with various degrees of success, in the Americas, Europe, and Asia. But the most significant change came in the area of vocal reinforcement. By the early 1960s, it was standard practice in productions of musicals to use microphones to help project singers' voices over the orchestra. These microphones were typically spaced across the front of the stage for downstage pickup and hung in the fly loft for upstage pickup. But these systems were not ideal. In a typical installation, singers had to stand directly in front of one of the downstage microphones for best results. The cables connecting the microphones to the mixing console were also subject to radio-frequency interference caused by the stage lighting system.The development of affordable miniaturized wireless microphones in the 1980s significantly improved vocal reinforcement. Wireless microphones send their signal to the mixing desk via a small low-power FM radio transmitter hidden somewhere on the actor. The microphone is often placed in the actor's hair or mounted on a flesh-coloured headset mouthpiece. The accuracy of sound reproduction (sometimes referred to as “presence”) that is obtained by placing the microphone in close proximity to an actor's mouth is extremely high.The improvement in the quality of vocal pickup spawned other changes during the 1980s and 1990s. The mixing desk was moved from the isolated sound booth into the auditorium so the operator could hear what the audience was hearing and vary the sound mix accordingly. Where a musical's budget was large enough, it became standard practice to place microphones among the orchestra as well as on the lead singers so the sound operator could balance the levels of each for the best result.The use of wireless microphones soon expanded beyond musical theatre to every type of theatrical presentation. The advantages of audiences' being able to clearly hear actors were obvious. Also, the ability to modulate the loudness of an actor's voice allowed directors and sound designers to begin experimenting with the use of background music and effects throughout entire scenes in much the same way that movies and television used sound.The other significant technological development to affect the sound industry in the 1980s was digitization. Digital sound (digital sound recording) equipment—preamplifiers, amplifiers, mixing consoles, and so forth—began appearing early in the decade, although only in the late 1980s did such equipment become sufficiently affordable that it was adopted widely. While there is no question that a digital signal most accurately replicates an original sound, there was at the turn of the 21st century considerable debate among sound designers as to the quality of sound produced by analog and digital equipment. The debate centred on the aesthetic issue of whether digitally reproduced sound demonstrated the same “tonal warmth” as sound recorded using an analog signal.Role of the sound designerThe role of the sound designer is very similar to that of the scenic designer (see above Role of the scenic designer (stage design)). Sound designers first read a play's script to learn its plot and characters as well as its period, locale, mood, and so forth. Additionally, the designer searches the script for information specific to the sound design, such as onstage noises—the ringing of a telephone, for instance—as well as offstage noises such as trains or storms. The designer also looks for scenes in which sounds could be used to support the mood of the play. Often referred to as atmospheric sounds, these may not be specified in the script but can be added to help the audience understand the emotional and physical environments of the play. For example, Rain (1922), a play adapted from a short story by the English writer W. Somerset Maugham (Maugham, W. Somerset), is set in Pago Pago, a port city on the Pacific island of Tutuila, and takes place as a typhoon approaches and then engulfs it. A background track that replicates the sound of a gentle breeze and, over the last two-thirds of the play, builds into a full-blown typhoon would greatly assist in creating the tension-filled atmosphere of the play.After synthesizing information gathered from the script and production meetings, the sound designer begins the actual work of creating, recording, and editing the music and effects that make up the production's sound design. The sound designer also works to assemble the playback and vocal-reinforcement equipment that will be used when the production moves into the theatre. After all the sounds have been gathered and created, the sound designer edits them into a show file, which consists of digitized sound cues edited into the sequence in which they are to be used during the production. These cues are typically adjusted—they may be added, changed, or deleted, and loudness and cue placement may be altered—during the rehearsal period, but, once the show opens, they usually undergo no additional changes. However, the sound designer may oversee adjustments to the equipment reinforcing an actor's voice as the action is occurring. These “on the fly” adjustments are both normal and constant.J. Michael GilletteCostume designClassical theatrical costumeTheatrical costumes were an innovation of the Greek poet Thespis in the 6th century BCE, and theatrical costumes were long called “the robes of Thespis.” Athenians spent lavishly on the production and costumes at annual drama contests. Each poet was given a wealthy citizen, the chorēgos (choragus), who, encouraged by the honour of a separate state impresario's prize, tended to make the event a demonstration of his spending power.Actors in the earliest tragedies (tragedy) wore long, rich robes similar to those worn by the priests of Dionysus. To increase the height and importance of the principal actors, Aeschylus introduced the buskin, an elevated boot called in Greek a kothornos (plural kothornoi). It became one of the chief characteristics of the Greek tragic actor. The soles increased in thickness according to the status of the wearer. To balance his height, padding often was used to add bulk to the actor's stature. So that they could dance with ease, members of the chorus did not wear these boots. The performers were clad in stage tunics, called chitons (chiton), which were long-sleeved, high-girdled, and elaborately embellished, as were their long and short cloaks (himations and chlamyses). Aeschylus was renowned for the brilliant mounting and costuming of his tragedies, and by the time of his death, in the mid-5th century BCE, a traditional tragic costume had evolved. Each costume was rendered in a symbolic colour.The most important feature of the Greek costume was the mask, which indicated the character's age, sex, station, and customary mood. The masks were made of linen, cork, or wood and were skillfully carved and painted. Their funnel-shaped mouths are thought to have acted as megaphones to amplify the voice. In his Onomasticon, Julius Pollux (Pollux, Julius), a Greek writer of the 2nd century CE, gives a detailed account of the special features accorded to each character. He enumerates 30 masks used in tragedy and lists the characteristics of the comedy series, which are particularly exaggerated and grotesque. The onkos, a high ornate headdress, crowned some masks, adding height and thus importance to the wearer.In the Doric (Dorian) mimes (mime and pantomime) and Old Comedies (Old Comedy), the upper-class characters wore stage chitons and cloaks, and the lower classes and slaves wore short tunics, revealing pendant phalli. These character tunics were often worn under light-fitting vests and over grotesque padding of torso and buttocks. Mimic horses, satyrs, bird figures, and other animal imitations were much in evidence. Aristophanes, in The Wasps, The Birds, and The Frogs, calls for all manner of such figures and clothing (dress). Actors performed in skins and wore horses' heads, birdlike visors, and mock wings.In the later comedy (New Comedy) of Menander, the phallus and mythological elements were abandoned, for his intention was to represent urban life, and the costumes worn reflected this intention. Masks became more stereotyped; they were used over and over again for character parts in different plays. Colour symbolism still held great importance.Roman (ancient Rome) drama had its indigenous roots in the Etruscan mimetic dances. Mime, together with acrobatic dancing, became a favourite part of the day's entertainment at the games or circuses. Plays too were among the diversions; to satisfy the crowd's taste for realism and sensation, legions of spectacularly dressed soldiers were introduced to the tragedies. Costumes for tragedy were modeled on Greek styles; by Roman times the name cothurnus (from kothornos) had come to designate the tragic genre itself. Kings and queens in tragedies wore appropriate padding, tall wigs, and sleeved syrma (the robe corresponding to the chiton). Bands of bright hues decorated the costumes of happy characters, and gray, green, or blue those of fugitives. Gods and goddesses were distinguished by their insignia; seers were clad in woolen garments over a shorter, less-full syrma; and huntsmen rolled a purple shawl around their left arms. Slaves wore leather jackets and light breeches or braids indicating their barbarian origin. In the fabula palliata (Roman comedies on Greek subjects and based on Greek models), actors wore chitons and the pallium, a cloak resembling the himation. In the subsequent, similar fabula togata, actors were costumed in the mantle and toga. The heroes of plays dealing with Roman history, called fabulae praetextatae, wore togas with the praetexta decoration indicating magistrates.The fabula Atellana (rustic plays originating in southern Italy) were given both public and private performances. In the homes of patricians, young noblemen often took the parts of the standard characters—the bragging, greedy Maccus, the stupid Bucco, the foolish miser Pappus—wearing masks to disguise their identities. Their masks, known as personae, were decorated with hair; they were not worn by professional actors until introduced by the actor Roscius in the 1st century BCE. Before the introduction of masks, wigs (galeri) were worn. Also, Italian comedians wore a flat slipper called the succus.The garment peculiar to mime productions was a coloured patchwork jacket called a centunculus, and this name became applied to mime actors in general. At Corneto, a tomb painting depicts Stupidus (the fool of the mimes) wearing another coat covered with coloured patches, a tall pointed cap decorated with a tassel, and a square, short cloak known as a ricinium. Because of this garment, the mime players were also known as riciniati.As drama in Rome declined, the mimes introduced plays on the theme of the oldish cuckold and the frail and plotting lover, which reached its bawdiest levels during the 6th century CE, as did the pantomimes featuring lavish licentious entertainments. Such entertainment continued to be presented until the fall of the Roman Empire later in that century. Through the early Middle Ages, jugglers, fools, and small mime troupes roamed Europe.Medieval (Middle Ages) costumeOriginally, mystery plays (mystery play) were performed in a church before the altar, with the actors, priests, and clerics wearing church vestments. The miracle plays (miracle play), which retold incidents in the lives of saints, were also originally performed by clerics and actors. Inventories were kept of garments made and bought, and these lists indicate that Adam and Eve were clad in close-fitting white leather, God in bishop's robes, and Jesus in a simple white robe. Cain, Abel, Joseph, Lazarus, and other biblical characters appeared in contemporary clothes, hoods, pourpoints (doublets), or loose gowns. A female character was indicated by the simple addition of a kerchief on the head. During the 12th century, when the performances moved outside the church, priestly vestments were still the main costumes.When European (Europe) craft guilds (guild) became responsible for the mounting and dressing of these productions, their scenic plans became ornate and ambitious, and the early simplicity was lost. Exotic robes and angels with gilded limbs, halos, and ornate wings may be seen in the paintings of the 15th-century Flemish masters Lucas van Leyden, Hans Memling (Memling, Hans), and Jan van Eyck (Eyck, Jan van). Satan and his devils enjoyed great popularity with the large audiences. Their grotesque masks, lashing tails, fangs, and snouts in lurid blacks, reds, and blues are well recorded by artists of the period.Morality plays (morality play), which became popular toward the end of the 14th century, were concerned with allegorical subjects, and they used costumes to personify the virtues and vices, life and death, and similar abstractions. Bible stories and morality dramas were also taken through the streets on two-story pageant wagons (pageant wagon); these processions of gorgeously dressed groups and tableaux can be seen in 15th-century paintings such as Piero di Cosimo's Triumph of Theseus and Ariadne and Sandro Botticelli (Botticelli, Sandro)'s Triumph of Chastity.Renaissance costumeFrom the early 14th century, in addition to religious performances, secular theatre developed in the form of popular celebrations, spectacles, royal and ambassadorial entries, weddings, and other lavish entertainments that surrounded the royal courts. A monarch entering a town or dominion would do so with a large entourage in full pomp and heraldic dress. These entrances included a series of stops at stages placed at various intervals en route. Tableaux vivant and mimes were performed in costumes similar to those worn in the mystery and morality plays. With the gradual decline of church power and the revival of Classical ideas, Renaissance designers found their inspiration in the myths and legends of Greece and Rome.Countries and designers competed in the sumptuousness of their displays. The progresses in England, entrées in France, and trionfi in Italy were based on the triumphal processions of the ancient world. The monarch or emperor was glorified as the hero, and the monarch's entourage and vassals appeared in semiclassical grandeur. There were floats of allegorical figures and legions of splendour such as Caesar had never dreamed. The Italian designers, who included artists as eminent as Leonardo da Vinci, led the field.At court, the tragic, comic, and satiric dramas of Classical theatre were revived, with the addition of entertaining entr'actes. From these descended the intermezzi (intermezzo)—pantomimes that included song and dance. Again, the designers wished to appeal to the eye of the Renaissance public. The designer in charge of theatrical productions for the court of Mantua in the mid-16th century explained in his treatise on stagecraft that the Italian object was to captivate and charm the audience:I tell you especially that I make efforts to dress the actors always in as noble a fashion as is possible for me, but in such a manner that there is a sense of proportion among them, in view of the fact that the rich costume,…particularly in these times when pomp is at its highest peak, adds much reputation and beauty to comedies, and even more to tragedies. I would not hesitate to dress a servant in velvet or coloured satin, as long as his master's costume were embroidered or decorated with gold, so rich that there would be maintained the proper proportion between them…. I do my utmost to dress the actors very differently from one another, and this is of great help, both in adding beauty and in facilitating the understanding of the plot.In 1589 the sophisticated Florentine court produced an intermezzo called Harmony of the Spheres, a spectacular type of masque that incorporated music; it was the immediate forerunner of opera. Etchings of the grand ducal fetes in Florence of 1606, 1608, 1615, and 1616 show groups of dancers in towering plumed Classical helmets, Roman costume, and cuirasses (cuirass) (body armour) worn over doublets, with Roman labels (bands of cloth) hung from the cuirass, over breeches and hose, to cover the thighs. The Renaissance developed these labels into an exaggerated ornate skirt and named it the tonneler. Each item of costume was decorated with a profusion of curved ornaments, flowers, vines, and animal and human forms.Strongly influenced by these Florentine specialists during a visit to Italy, Inigo Jones (Jones, Inigo) transformed English court masques (masque) and entertainments in the early part of the 17th century. Through him, English designs followed the Italian pattern: breastplates molded to the body, plumes, helmets, and various Roman kilts mixed with modified elements of contemporary dress. Ladies' costumes followed the dress of the period more closely but strove for a looseness and for the transparency of fabric typical of Classical dress. Décolletage and low-cut bodices were much in evidence, with bosoms often veiled with gauze. The cost of these costumes was borne by the wearers, the lords and ladies of the court. There seemed at times no limit to their embroidered, bejeweled luxury and fine headpieces.Little pictorial evidence of the first public theatres in England survives. It is known, however, that the best part of the actors' wardrobes was gifts from wealthy patrons. One drawing of William Shakespeare's Titus Andronicus dated 1595 shows contemporary costume mixed with costume à la romaine similar in design to the courtly work of Jones. Mixtures of styles and periods were accepted by the audiences. Certain famous characters, such as Shakespeare's Sir John Falstaff (Falstaff, Sir John), became identified with a particular type of dress; a sketch that Jones made of Sir William Davenant (Davenant, Sir William) in The Temple of Love, produced in 1635, was inscribed: “a robe of russet girt low with a great belly…the sleeves short…buskins to show a great swollen leg…a great head and bald. Like a Sir John Falstaff.”In Italy the commedia dell'arte presented a multiplicity of characters and types. The players' fine costumes evolved from garments representing different Italian (Italy) provinces and rustic personalities and gradually became stylized, subject to the dictates of changing taste. To make the costumes decorative or funny, there were exaggerations in form and colour. The characters of the lovers appeared in contemporary street clothes, and comic personages in curious or grotesque garb with leather half-masks. These were ideal theatre clothes, for they identified the characters, allowed complete freedom for movement and acrobatic dancing, and charmed the spectator with their amusing devices, patterns, and colour motifs. A typical character, Arlecchino (Harlequin), originally dressed in shreds and patches, had emerged by the 17th century in a suit of red, blue, and green triangles arranged symmetrically and joined together with yellow braid. One hundred years later, the triangles became diamonds, and his soft cap was exchanged for a pointed one. From the 18th century onward, he appeared as Harlequin, a central character in English pantomime (mime and pantomime), carrying his original wooden sword and wearing his black mask. A fine pictorial record of the commedia characters may be seen in the works of the 17th-century French artists Jacques Callot (Callot, Jacques) and Antoine Watteau (Watteau, Antoine).The commedia troupes performed throughout Europe, and the theatrical form was especially popular at the French court. Molière's company also toured France in improvised farces based on the style of the commedia. Actors in his comedies played in contemporary dress, but they also performed with the king and court in brilliantly dressed spectaculars at Versailles. Texts were by Molière, music by Jean-Baptiste Lully (Lully, Jean-Baptiste), and costumes and decor by Jean Berain the Elder (Berain, Jean, the Elder).The Restoration of the English monarchy in 1660 led to the opening of theatres again, and the great innovation was the introduction of actresses. Talented, confident, and flamboyant ladies replaced the Elizabethan boy actors. Records indicate that “splendidly clothed” persons lent costumes, and wardrobe keepers aided players in selecting from available stock. No attempt was made at character dressing or historical accuracy.A galaxy of specialists joined the courts of the French kings Louis XIII (Louis XIV style) and Louis XIV, with Giacomo Torelli (Torelli, Giacomo), the chief originator of Baroque theatre, arriving from Venice. This monumental scenic style included magnificent colonnades, temples, palaces, and scenes so lavish that only the great ruling houses could afford them. Designers such as Torelli brought great prestige to their patrons. An outburst of Baroque opulence bore witness to the power and splendour of the Sun King. In France in the early 17th century, the designer Daniel Rabel worked inventively, producing many witty and droll effects and costumes of grotesque conception. Burlesque costume had found its way to amuse the court.Berain (Berain, Jean, the Elder) and Henri Gissey were attached to the Royal Cabinet of Louis XIV. Gissey is most famous for his celebrated Carrousel (1662), a horse spectacular never since surpassed in its magnificence—500 noblemen in plumed regalia escorted by a greater number of elaborately dressed attendants. Costumes represented different nations, each having a particular colour scheme: the Romans, led by the king, were in red and gold, the Ottomans in black and yellow, the Indians in white and gold, and the Americans in green and gold. The scene, played in front of the Louvre, was indeed the grandest fantasy in costuming, with both horses and riders decorated in full Baroque trappings.Chroniclers record gorgeous costumes appearing in 17th-century ballet, opera, and dramatic offerings; gold brocades covered with lace, diamonds, emeralds, ribbons, and immense trains graced the stages of France. The French surpassed the Italians in their opera costumes, which were richer than any elsewhere. In the designs of Berain there is a homogeneity of style that is the mark of a great master. Berain's costumes for women, which were based on contemporary court dress, were serious and noble in style. Their tight bodices and flared basque shirts had decorative overskirts with trains; they followed an almost uniform silhouette. The headdress, also carefully designed, was a formal arrangement of feathers or lace. Male garments were in the Roman style, the tunic fitting tightly to the chest, worn with tonneler (short skirt), high boots, and cape. To avoid monotony, Berain devised an amazing variety of ingenious trimmings—embroideries, fringes, slashings, puffs and paddings, inlaid ornamental motifs, pastes, and semiprecious stones to punctuate every small decorative panel and part. Scaly or bejeweled bodies, serrated leaves—every elegant or fantastic theatrical device was used to create a sophisticated ensemble. Berain coordinated all aspects of scenic decor in an equally industrious way and as a decorative artist dominated French and European taste and costume design. After Berain died in 1711, the sumptuous Baroque of the early years of Louis XIV declined. Berain's son Jean succeeded his father as court designer and carefully documented his father's drawings.Created in 1721, Claude Gillot (Gillot, Claude)'s designs for the ballet Les Éléments showed a great change in taste. The heavy fabrics and embroideries used by Berain were replaced by lighter, more delicate weights and appliqués. Ladies' costumes, following the caprices of the contemporary modes, included a pannier. Peasant and rustic characters began to appear and were most popular with the court, in beribboned garments of pastel satins and silks. Extensive records of these costumes exist in the form of engravings.Costume of the 18th and 19th centuriesJean-Baptiste Martin, who was appointed designer for the Paris Opéra in 1748, devised decorative and amusing Rococo (Rococo style) variations for the male dancer's traditional costume. Martin utilized Inca, African, Chinese, and Mexican motifs in his ballets, and under his direction the tonneler took on an elliptical shape.All the elegance and sophistication seen in the Rococo court circles of Louis XV were brought to the stage by Martin's successor, Louis-René Boquet. His designs were theatricalized versions of the new fashionable silhouette. Boquet clothes were delicate, artificial, and pale in tone, trimmed with garlands and Rococo finery. All of Europe imitated the French (France) ideas, although the English and German facsimiles lacked Boquet's innate good taste.French philosophe Denis Diderot (Diderot, Denis) wrote in 1758 of the fashions then current in the French theatre:Ostentation spoils everything…. Wealth has too many caprices: it can dazzle the eye, but not touch the heart. Beneath the garment that is overloaded with gilding, I never see more than a rich man, and it is a man I look for….Comedy ought to be played in informal dress. On the stage it is not necessary to be either more or less dressed up than one is at home….The more serious the play, the more austerity there must be in costume….What expense were not our actors put to for the production of l'Orphelin de la Chine? How much has it not cost them to rob this work of part of its effect?In 1755, in the first production of Voltaire's play L'Orphelin de la Chine (The Orphan of China), the great French actors Lekain and Mlle Clairon (Clairon, Mlle)—who, like Diderot, were bent on more simplicity and historical accuracy—performed without the hoops or overskirts of then fashionable dress. Similarly, the men appeared dressed as Tatars and Chinese. In 1789 the French tragedian François-Joseph Talma (Talma, François-Joseph) provoked a scandal by appearing in Voltaire's Brutus (first performed 1730) in a severely simple toga appropriate to the ancient Roman setting of the play.In England David Garrick (Garrick, David) abandoned heroic Roman garments in favour of realistic contemporary dress, which he designed himself to ensure the simplicity he desired. The Irish actor Charles Macklin (Macklin, Charles) became the first to play Shakespeare in authentic “ancient dress” when he appeared on the stage in 1773 as Macbeth in a Highland military habit.Public knowledge of historical costume was increasing by the 19th century, though some critics disapproved, believing it weakened the plot. But the thirst for historical accuracy won the day, in part because of the efforts of its major champion, the 19th-century English playwright and antiquary James Robinson Planché. A playbill of a Planché production of 1824 read:Shakespeare's Tragedy of King John with an attention to Costume never equalled on the English Stage. Every Character will appear in the precise HABIT OF THE PERIOD, the whole of the Dresses and Decorations being executed from indisputable Authorities.…King John's Effigy in Worcester Cathedral…Queen Elinor's Effigy in the Abbey of Fontevraud.…Illuminated Mss in the British Museum, Bodleian and Bennet College Libraries…&c.Planché's success amply reimbursed the management for the enormous expenditures required to make even the meanest extra's garments authentic. Correct costumes became the order of the day. The actor-manager Charles Kean (Kean, Charles) splendidly mounted a series of Shakespearean productions in London in the 1850s. In Germany, August Wilhelm Iffland (Iffland, August Wilhelm)'s productions closely followed the same reforms, and costume designers were urged to emulate the past.Dancers (dance) too wished to be liberated from the pannier and tonneler. In Pygmalion, a ballet of her own composition, Marie Sallé (Sallé, Marie) danced in London in 1734 dressed only in a muslin robe like that of a Greek statue; she wore no panniers, petticoat, or bodice, and her hair was loose and without ornament. The French ballet master Jean-Georges Noverre (Noverre, Jean-Georges) had advocated drastic reform in dance dress as early as 1760. He proposed to put his dancers in simple draperies of contrasting colours, worn in such a manner as to reveal the figure in movement. Both male and female dancers became increasingly impatient with the hampering Rococo conventions, and, as dancing technique grew more intricate, designers prepared innovations that anticipated general developments in fashion. By the end of the 18th century, every woman had abandoned her panniers.Civil codes at the start of the 19th century greatly aided those who would reform theatrical costume. The fashion for classical robes and tunics modeled on Greek and Roman patterns took to the streets; the high-heeled shoe was replaced by a flat slipper.Auguste Garneray and Hippolyte Lecomte were leading French ballet designers in the 19th century. The former's work shows ingenuity in adapting contemporary dress to suggest different lands and other periods. The latter was originally a painter of historical episodes; accuracy rather than imagination is the distinguishing quality of his designs. In 1832 the influence of the Romantic period was first seen in ballet with a production of La Sylphide. Eugène Lami designed a muslin dress, an ethereal costume that became the new uniform of the classical dancer, for Marie Taglioni (Taglioni, Marie), the greatest dancer of her day.Opera and dramatic productions followed Planché's regard for period and regional detail. Unfortunately, the elaborate stage settings and the costumes were seldom coordinated successfully. This led George II, duke of Saxe-Meiningen (George II), to design his own productions, as he wished to achieve an integrated style. He was the first of the directors who controlled all aspects of production. His example was followed by the most prominent directors of the 20th century.Amid spectacular scenery, large ensembles danced and mimed in fanciful versions of contemporary and historical dress in the ballet extravaganzas of the 1880s (forerunners of the Folies-Bergère revues of Paris) that played at La Scala in Milan and the London Alhambra. The ingenious designer C. Wilhelm (original name C. Pitcher) translated insects, flowers, birds, and reptiles into dance costumes. The main interest of most designers, however, lay in framing the female figure, and many theatrical costumes were designed to reveal as much as the law permitted.Costume of the 20th century and beyondAt the turn of the 20th century, the theories of the Swiss stage designer Adolphe Appia (Appia, Adolphe) and the English actor and designer Edward Gordon Craig (Craig, Edward Gordon) called for symbolism and voiced a strong reaction against the naturalism of the Meiningen Company and the Moscow Art Theatre. Appia advocated that stage costume evoke and suggest but never copy historical lines.A painters' theatre arose after Sergey Diaghilev (Diaghilev, Sergey Pavlovich)'s presentation of the Ballets Russes in 1909 in Paris. The brilliant palettes and well-coordinated decors of this ballet—by Léon Bakst (Bakst, Léon), Alexandre Benois (Benois, Alexandre), and Nicholas Roerich (Roerich, Nicholas)—were praised. Natalya Goncharova (Goncharova, Natalya)'s design for Le Coq d'or in 1914 was unprecedented in its use of vivid colours, chiefly shades of red, yellow, and orange, with other colours for discordant emphasis. The forms of the costumes and their decorations were based on traditional Russian folk dress, though that dress was transformed and made uniquely of their epoch by the jagged influence of Cubism. Avant-garde artists of many of the flourishing movements of modern art—Cubists, Constructivists (Constructivism), and Surrealists (Surrealism)—brought about an acceleration of innovation in design concepts, which in previous centuries had evolved gradually throughout Europe.Appia, Craig, and Diaghilev led others to experiment. Vsevolod Meyerhold (Meyerhold, Vsevolod Yemilyevich)'s 1907 production of Leonid Andreyev (Andreyev, Leonid Nikolayevich)'s play The Life of Man, with expressionistic costumes designed by Theodore Komisarjevsky (Komisarjevsky, Theodore), was purely mechanical in its design. German advocates reasoned that, since the actor is enclosed in the space of the stage, either the stage must be arranged according to the illusion of reality so as to fit the actor as a “natural” human being, or the actor must be transformed to match the cubist and abstract space of the stage.As modern dance evolved, its rapid rhythms and pace offered the costume designer new challenges and scope for original work. The productions of Merce Cunningham (Cunningham, Merce) and Alwin Nikolais (Nikolais, Alwin) in New York City presented unique shapes that attempted to express the exploration of time and space. Nikolais made his costumes part of a total stage design, a theatrical abstraction of the way he saw humankind, as part of a socioeconomic mechanism—an agreeable but not a central part. Accused of dehumanizing the dancers, he maintained that their role was to be an expression of a greater state of being for humankind, of the experience of living in a world of motion, sound, colour, and action that strongly affects them and is affected by them.The rise of the American (United States) musical owes much to the close collaboration of composers, writers, and choreographers with designers. In a musical the costume designer's task is manifold. The designs must capture the spirit of the music and lyrics, interpret the period, heighten the characterization of the actors, and help the dancers in their varied, often athletic routines. The costumes for My Fair Lady (1956) and West Side Story (1957) were especially successful in these respects.The radical creative talents of the German playwright Bertolt Brecht (Brecht, Bertolt) created new production concepts and styles; the clothes worn conveyed to the audience in a satirical fashion not only a characterization of the wearer but also his social status. Another compelling force in 20th-century experimental theatre, Jerzy Grotowski (Grotowski, Jerzy), conceived his production of Akropolis at the Polish Laboratory Theatre in 1962 as a poetic paraphrase of an extermination camp. There is no hero—and no individuality—among the characters. The costumes were bags full of holes covering naked bodies, and the holes were lined with material suggesting torn flesh; wooden shoes covered the feet, and anonymous berets the heads. The second half of the 20th century was a time of social upheaval throughout the world, but particularly in the United States and Europe, where costume design reflected the changes. Directors such as Jean-Louis Barrault (Barrault, Jean-Louis) in France and Jürgen Flimm in Germany as well as theatre groups such as the Living Theatre (Living Theatre, The) explored political and social themes with innovative methods and techniques to which costume was essential. Regardless of how societal changes affected the manner in which stories were told in the theatre, the one constant across the diverse range of presentational modes was the design dictum that costume had to express the mood and spirit of a play. That design philosophy persisted through the turn of the 21st century.Maureen Heneghan Tripp Clive Barker J. Michael GilletteCostume in Noh and Kabuki theatreIn Japanese Noh (Noh theatre) and Kabuki theatre, almost every element of a production is dictated by tradition. Noh costumes, which evolved into their modern form in the 14th and 15th centuries, are no exception. The type of character being portrayed is revealed through the application of conventions in the design and construction of a costume. The details of the design—the silhouette chosen, the colour combinations, the richness and texture of the fabric, and the type and amount of detail—all combine to give indications of character as well as to make a strong visual impact.From its origins in the early 17th century, Kabuki was to a great extent shaped by governmental restrictions. While scripts frequently called for aristocratic characters—nobles or samurai—it was prohibited to imitate the dress of either of these classes. Kabuki production companies responded by exaggerating the colour and fabrics of that dress. As a result, theatrical costumes typically became more colourful and more sumptuous than the clothing styles on which they were based. The silhouette of robes and gowns was also overstated: if the shoulders of the original robes were slightly padded, the shoulders of the costume were higher and wider. So too, to evade restrictions on the use of printed silk, a fabric commonly used by the aristocracy, production companies often embroidered rich patterns onto silk or used appliqués. Most of the classical traditions of Kabuki, including costuming, date from the first half of the 17th century. While the governmental prohibitions that created these traditions disappeared over the ensuing centuries, the style of Kabuki has remained relatively unchanged since that time. Despite their visual extravagance, however, Kabuki costumes are even today full of subtlety, illusion, and hidden meaning, all of which help to clarify a character's role for a knowledgeable audience.J. Michael GilletteTheatrical makeupWestern traditionsTheatrical makeup is the practice of painting, enhancing, or altering the face, hair, and body of the actor with cosmetics, plastic materials, and other substances; it is also the collective term for the materials used in making up. Actors have used makeup in the theatre for a long time, not only to look their best and to transform their appearance but also to ensure that they will be seen and recognized by the entire audience. How well an actor is seen depends upon the distance between the actor and the farthest spectator as well as the amount of available light. Distances blur the features and make recognition of the actors extremely difficult for the spectators.It is impossible to say when the first actor daubed paint on his face in an attempt to make his performance more effective. Some maintain that Thespis, the first actor to step out of the chorus in Greek theatre in the 6th century BCE, smeared his face with white lead and red cinnabar. He may have done so, but the very large size of some of the Greek theatres (containing up to 15,000 spectators) made the use of the masks (mask) a more practical solution. Not only did masks enable the actor to play more than one role, but their larger-than-life size and exaggerated features also enabled the audience to identify the actor's role from a distance.The Roman (ancient Rome) theatre borrowed and continued the use of the mask. Evidently some actors thought that their own faces would be more effective, however, since there are contemporary descriptions of certain mimic actors with painted faces. Like the Roman mimes (mime and pantomime), the traveling actor-comedians of the Italian commedia dell'arte in the 16th century developed a set of stock characters using masks. There may have been some continuity of tradition, for there are resemblances between the comedians' leather masks and those of the Roman farces.As actors in 17th-century Europe began to perform in permanent theatres, in which they were separated from the audience by the proscenium arch, they had to deal with the problem of making the face look distinctive in illumination from candles and oil lamps. It is probable that the actors adapted the cosmetics (cosmetic) of fashionable women to their own use.The use of cosmetics increased greatly during the 18th century. Women, and men to a lesser extent, painted their faces with lead oxide for a pale complexion and cinnabar (mercuric sulfide) for rouge. Both were poisonous compounds. With the widespread use of cosmetics, it was noticed that paler faces were easier to see in dim light. By the 1770s the use of white paint was general upon the stage even though it tended to conceal the expressive motion of the muscles.The introduction in the early 19th century of limelight, which was followed by gas lighting and arc (arc lamp) lights, created the necessity for a more subtle use of cosmetics on the European and American stage. The actor's palette consisted at this time of white chalk, carpenters' blue chalk, papers impregnated with red colouring, and India ink. Some actors were known to make up their faces with whitewash rubbed off the walls, dust scraped from red bricks, and black from burned paper or cork or a burned match. Credit for the invention of greasepaint belongs to Carl Baudin of the Leipziger Stadt Theatre. Wishing to conceal the join between the front edge of his wig and forehead, he mixed a flesh-coloured paste of zinc white, yellow ochre, vermilion, and lard. By 1890 theatrical greasepaints were available commercially in many colours, and other items of makeup also began to be manufactured for use in the theatre.The practice of makeup in Western theatre changed greatly with the wave of vitality that swept over the theatre after World War II. As the stage was thrust into the auditorium and the audience was arranged on all sides of the acting area, the actor was brought closer to the spectator, which made close scrutiny possible. Poorly executed and heavy makeup looked obvious, and several time-honoured practices had to be abandoned. Red dots in the corners of the eyes and the use of bright eyeshadow (which had first been used to counteract the effects of footlights) appeared ridiculous. Actors began to reject greasepaint in favour of a makeup that had been developed for the motion-picture industry, a water-soluble cake makeup capable of being spread in a thin wash of colour. It made a completely natural look possible. The desire for naturalism in appearance became the overriding concern.Many improvements in makeup techniques were developed primarily for films and television and were then rapidly adopted in Western theatre. There was a great change in theatrical wigs (wig), for example, which once had a band of silk that was blended with colour into the forehead. This type of wig was not successful for film work, since the join was obvious to the camera. A new type of wig was developed that was made with an edge of plastic lace into which hairs were knotted. With the lace glued to the forehead, the hairs seem to grow from the skin, and the result is a natural-looking hairline.During the second half of the 20th century, makeup was increasingly included in the total production design. What was once considered the prerogative and responsibility of the individual actor came to be influenced by designers, directors, and makeup artists. At the end of the 20th century, larger theatrical companies employed a staff of makeup artists responsible for ensuring that each makeup was executed as designed and that the style was consistent. After midcentury, rubber latex makeup also came into use to give the skin the textured look of extreme old age, to make bald caps, to make realistic-looking false noses, and to make jowls and other forms of sagging flesh.The ideology of many alternative theatre groups that emerged after World War II led to their rejection of makeup. In these theatre companies the actor did not seek to hide behind a character but was instead present as himself in public, relating directly with the audience. The Living Theatre (Living Theatre, The) was one such company. Even when named roles were assigned, the actor was clearly visible beneath the role. In theatre such as this, the use of makeup was anathema in its illusionistic sense but was used in a ritualistic sense. Experiments in ritual theatre resulted in the use of masks and highly decorative or symbolic makeup, as is found in jingxi (Beijing opera) in China or Kabuki and Noh theatre in Japan.Western laboratory theatre companies of the second half of the 20th century concentrated on the actor's control of the processes of transformation. Grotowski (Grotowski, Jerzy) encouraged the actor to try to transform himself without the help of makeup. If makeup was used only after all the other possible changes of character had been explored, then its use, Grotowski believed, would be much more expressive. The growth of the alternative theatre circuit in Britain in the 1960s and '70s, which brought performances to small intimate rooms, similarly pushed the actor to try all means of characterization other than makeup, which appeared grotesque at close range.With the exception of stylized productions—such as of the musical Cats (1981), in which actors resemble cats—makeup in the nonexperimental, commercial theatre of Europe and North America during the late 20th century tended to be very naturalistic. By the turn of the 21st century, stage lighting had generally become very natural in colour and intensity; makeup had likewise become more natural in appearance.Stanley Dufford Clive Barker Ed.Chinese and Japanese traditionsLike other Asian theatrical traditions, almost every element of jingxi, including makeup, is rigidly controlled by convention. Actors playing the roles of men and old women wear simple makeup. All actors playing male roles, except those of young heroes, wear beards. For female roles other than old women, an actor's face is painted white with the area immediately around the eyes coloured a deep red that shades into pink. Actors playing unbearded male roles wear a white base, but the contrasting colour around the eyes is less pronounced. The makeup for the so-called painted-face roles is the most spectacular. It uses brilliantly coloured, elaborately patterned designs that are symbolic of the specific role the actor is playing. While white patches around the eyes are a common feature of all comic roles in jingxi, primarily black patterns are used to identify the specific type of each clown.Japanese Noh (Noh theatre) and Kabuki theatres offer different visual treatments of the actor's face. In Noh the characters, typically played by mature men, wear masks (mask) rather than makeup. These masks, which generally portray either a neutral or a very strong emotion, depict stock character types found in traditional Noh scripts: women, deities, old men, mythological beasts, and so forth. The appearance of the masks is dictated by tradition, which enables audiences to recognize specific character types. In those few roles for which masks are not required, the actors traditionally hold their faces in a fixed masklike attitude.In Kabuki, makeup is used rather than masks. The makeup style known as kumadori (literally, “to follow lines”) exaggerates all facial lines and features. It is generally used for emotionally charged roles—strong masculine characters, mythological gods, and beasts. While the kumadori style of makeup follows the actor's natural facial lines, the specific design mirrors the emotional nature and social station of the character being portrayed. Makeup for less emotionally charged characters tends to be less spectacular than the kumadori style.The colours used in Kabuki makeup, like everything else about Kabuki, are dictated by tradition. The base colour for almost all makeup designs is white, thought to be have been chosen so as to help project the actor's face in early, dimly lit Japanese theatres. There are also specific meanings associated with specific makeup colours: indigo represents ghosts and evil characters, for instance, while brown is used for gods and evil nobles. Likewise, deep red represents deep anger or hostility. This colour-coding also helps to clarify a character's role for an experienced Kabuki audience.J. Michael GilletteAdditional ReadingAspects of stage setting and scenery are explored in Walter René Fuerst and Samuel J. Hume, Twentieth-Century Stage Decoration, 2 vol. (1929, reissued 2 vol. in 1, 1967); Lee Simonson, The Stage Is Set (1932, reprinted 1975); Léon Moussinac, The New Movement in the Theatre (1931, reissued 1967); Mordecai Gorelik, New Theatres for Old (1940, reprinted 1975); Andrew McCallum, Fun with Stagecraft (1981); Thurston James, The Prop Builder's Molding and Casting Handbook (1989); Francis Reid, The Staging Handbook, 3rd ed. (2001); Daniel A. Ionazzi, The Stagecraft Handbook (1996); George C. Izenour, Theatre Technology (1996); Susan Crabtree and Peter Beudert, Scenic Art for the Theatre: History, Tools, and Techniques (1998); J. Michael Gillette, Theatrical Design and Production, 4th ed. (1999); Warren C. Lounsbury and Norman C. Boulanger, Theatre Backstage from A to Z, 4th ed. rev. and expanded (1999); Alys E. Holden and Bronislaw J. Sammler, Structural Design for the Stage (1999); William H. Lord, Stagecraft 1: A Complete Guide to Backstage Work, 3rd ed. rev. (2000); and Christine A. White, Technical Theatre: A Practical Introduction (2001).Stage lighting is explored in Theodore Fuchs, Stage Lighting (1929, reissued 1963); Richard Pilbrow, Stage Lighting Design: The Art, the Craft, the Life (1997); Max Keller (compiler), Light Fantastic: The Art and Design of Stage Lighting (1999); Steven Louis Shelley, A Practical Guide to Stage Lighting (1999); Francis Reid, Discovering Stage Lighting, 2nd ed. (1998); Neil Fraser, Stage Lighting Design (2000); Graham Walters, Stage Lighting: Step-by-Step (1997); J. Michael Gillette, Designing with Light: An Introduction to Stage Lighting, 4th ed. (2003); and Linda Essig, The Speed of Light: Lighting Professionals on Technological Change (2002). Costumes are examined in Jack Cassin-Scott, Costumes and Settings for Staging Historical Plays, 5 vol. (also published as Costumes and Settings for Historical Plays, 1979–80); Millia Davenport, The Book of Costume, 2 vol. (1948, reissued in 1 vol., 1979); Hilaire Hiler and Meyer Hiler, Bibliography of Costume: A Dictionary Catalog of About Eight Thousand Books and Periodicals (1939, reissued 1967); Jack Cassin-Scott, The Illustrated Encyclopaedia of Costume and Fashion: From 1066 to the Present, rev. and expanded ed. (1998); and Sylvia Moss, Costumes and Chemistry (2001). Hair and makeup for the stage are explored in Richard Corson and James Glavan, Stage Makeup, 9th ed. (2001); Richard Corson, Fashions in Hair: The First Five Thousand Years, 9th ed. (2001); and Rosemarie Swinfield, Period Make-up for the Stage (1997). Oscar G. Brockett and Franklin J. Hildy, History of the Theatre, 10th ed. (2008), provides a useful overview of many of these subjects.
* * *
Look at other dictionaries:
New York Studio and Forum of Stage Design — The Studio and Forum of Stage Design was started by Lester Polakov in Greenwich Village, NYC (circa mid 1960 s). Mr. Polakov was born in Chicago in 1916 and studied in New York with George Grosz and at Columbia University. He began his career… … Wikipedia
input stage design — įėjimo pakopų projektavimas statusas T sritis radioelektronika atitikmenys: angl. front end design; input stage design vok. Front End Design, n rus. проектирование входных каскадов, n; разработка входных каскадов, f pranc. conception des cascades … Radioelektronikos terminų žodynas
Design Review — was a publication of the Wellington Architectural Centre. The Centre was founded in 1946, and began the first architectural school in Wellington (1947) and the first town planning school in New Zealand (1949). The Centre was unique at the time of … Wikipedia
Stage (theatre) — For other uses, see Stage (disambiguation). Actors performing on the stage of the Drury Lane Theatre, 1674 … Wikipedia
stage machinery — Devices designed for the production of theatrical effects, including rapid scene changes, lighting, sound effects, and illusions. Such devices have been in use since the 5th century BC, when the Greeks developed a crane to lower to the stage an… … Universalium
Design Review (publication) — This article is about the magazine, for the military and government engineering design life cycle, see: Design review. Design Review was a publication of the Wellington Architectural Centre. The Centre was founded in 1946, and began the first… … Wikipedia
design — /di zuyn /, v.t. 1. to prepare the preliminary sketch or the plans for (a work to be executed), esp. to plan the form and structure of: to design a new bridge. 2. to plan and fashion artistically or skillfully. 3. to intend for a definite purpose … Universalium
Stage lighting instrument — Stage lighting instruments are used in stage lighting to illuminate theatrical productions, rock concerts and other performances taking place in live performance venues. They are also used to light television studios and sound stages.Terminology… … Wikipedia
Design for manufacturability — (also sometimes known as design for manufacturing) (DFM) is the general engineering art of designing products in such a way that they are easy to manufacture. The basic idea exists in almost all engineering disciplines, but of course the details… … Wikipedia
Design management in organization — involves creating the means to accomplish the stated mission or objective. To design means to function according to a plan. The design establishes the relationships among the various parts of the organization (or the system), linking them… … Wikipedia